Rivera-primo SharpEye Kicker Manuel d'utilisateur télécharger pdf

The purpose of the SharpEye

kick start assembly is to provide kick start capabilities to 5 and 6

speed Big Twin transmissions. This is accomplished by removing the stock transmission clutch re-

lease cover and installing your new Rivera Primo

SharpEye

kick start assembly.

Tools

Needed:

1/8”, 3/16”, 5/16” socket head wrenches

(2) 9/16” open / box wrenches

1 ½” socket, (We recommend Jim's Machine socket p/n 1030-TS)

1 1/16” socket

Assembly

Procedure:

1. Disconnect battery ground wire.

2. Remove transmission drain plug and drain oil.

3. Remove clutch release cover and gasket.

4. Remove clutch cable from original cover.

5. Place the Sharpeye cover on the transmission trapdoor and check the clutch cable the clutch

cable routing and adjust as necessary.

Disassembling Kickstart Mechanism For Clutch Cable Installation.

1. Remove the 14 tooth pinion gear (1216-0100), by turning the

drive gear (1216-0101). Accomplish this by using the kick arm or wrench and turning the

square end of the kick shaft (1219-0001) about 1/8 turn. This releases the pinion gear (1216-

0100). Place the pinion gear (1216-0100) and the spring (1217-0014) aside.

2. Remove the flathead screw (1100-0049) and retainer washer (1217-0015) that holds the drive

gear (1216-0101) to the shaft (1219-0001).

NOTE: Mark the shaft (1219-0001) and the gear (1216-0101) so you can return them to the same rel-

ative position. The return spring slot, on the shaft (1219-0001), is 90 degrees clockwise to the stop

pin on the 19 tooth drive gear (1216-0101), as viewed from the outside to the inside.

3. Using the kicker arm or a wrench, release the return spring

pressure that is against the 19 tooth drive gear (2016-0101) and remove the drive gear (2016-

0101).

4. Allow the kicker arm return spring (1217-0011) to

unwind by allowing the cover to rotate slowly.

NOTE: Under the 19 tooth drive gear (1216-0101), sandwiched between thrust washers is a radial

bearing (1018-0011), The thin thrust washer (1100-0047)) goes in first, then the radial bearing (1018-

0011), with the thicker thrust washer (1100-0048) next to the 19 tooth drive gear (1216-0101).

5. Remove the three flathead socket screws (1100-0049) flanged pinion gear bushing (1217-

0006) and remove the flanged pinion gear bushing.

6. Remove the clutch release lever (1217-0007) and cable connector

(1217-0009).

RIVERA PRIMO INC.

12450 WHITTIER BLVD.

WHITTIER, CA 90602

562-907-2600

1 2

Résumé du contenu

Page 1

The purpose of the SharpEyeTMkick start assembly is to provide kick start capabilities to 5 and 6speed Big Twin transmissions. This is accomplished by

Page 2

NOTE: Do not lose or misplace the three 3/8" chrome balls (1217-0010).ASSEMBLY1. Install the cable in the per your OE service manual.2. Re-assemb

Commentaires sur ces manuels

Pas de commentaire

Rivera-primo SharpEye Kicker Manuel d'utilisateur

Naviguer en ligne ou télécharger Manuel d'utilisateur pour Pour la voiture Rivera-primo SharpEye Kicker. Rivera Primo SharpEye Kicker User Manual Manuel d'utilisatio

Résumé du contenu

Commentaires sur ces manuels

Produits connexes et manuels pour Pour la voiture Rivera-primo SharpEye Kicker